Which Hi-Power Lithium Battery Suits Each Elco Electric Outboard

We get asked this most weeks, so here is the arithmetic in one place: which Hi-Power lithium pack actually suits which Elco electric outboard, and why.

Two numbers decide every one of these pairings — the motor's system voltage, which has to match the pack, and the motor's maximum current draw, which has to sit inside the pack's continuous rating. Capacity decides how long you run; it does not decide whether the combination works at all. People usually shop on capacity and get caught by current.

Elco EP outboard electrical specifications

From Elco's own published outboard spec sheet:

Model Comparable gas HP System voltage Input power Max current draw
EP-5 5 HP 24 V 3,000 W 125 A
EP-9.9 9.9 HP 48 V 4,704 W 98 A
EP-14 14 HP 48 V 6,480 W 135 A
EP-20 20 HP 48 V 8,400 W 175 A
EP-30 30 HP 96 V 12,480 W 130 A
EP-50 50 HP 96 V 26,400 W 275 A

Note the EP-30 and EP-50 are 96 V motors. That matters, because it means two 48 V packs in series — and not every pack can be series-wired.

Hi-Power pack ratings

Pack Nominal Energy Continuous current Series capable
HP24-120Ah 24 V 2,880 Wh 200 A —
HP48-105Ah 48 V 4,800 Wh — No
HP48-160Ah 48 V 7,680 Wh 225 A Yes
HP48-200Ah 48 V 9,600 Wh 250 A Yes
HP48-250Ah 48 V 12,000 Wh 400 A Yes

The pairings, with full-throttle runtime

Runtimes below are wide-open throttle — energy divided by input power. Treat them as the floor, not the expectation. Displacement boats spend most of their time at a fraction of rated power, and at roughly half throttle you can expect something near double these figures. Hull, load and conditions move the real number more than the battery does.

EP-5 (24 V, 125 A)

The HP24-120Ah is the match — 24 V, and its 200 A continuous rating clears the EP-5's 125 A draw with room to spare. About 1 hour at full throttle from 2,880 Wh, call it 2 hours at a half-throttle cruise.

EP-9.9 (48 V, 98 A)

The easiest motor to supply — 98 A is modest, so current is never the constraint and you are choosing purely on how long you want to run:

EP-14 (48 V, 135 A)

All four 48 V packs clear 135 A. The 200Ah gives about 1.5 hours WOT and the 250Ah about 1.9 hours. The 100Ah will run it, but at 0.74 hours WOT it is thin for anything but short hops.

EP-20 (48 V, 175 A)

Still inside every 48 V pack's continuous rating, but the margin is narrowing — 175 A against the 160Ah's 225 A. We would put the 200Ah (about 1.1 hours WOT) or the 250Ah (about 1.4 hours) behind an EP-20 and not go smaller.

EP-30 (96 V, 130 A) — two packs in series

A 96 V motor needs two 48 V packs wired in series. The current draw is a comfortable 130 A, so the pack choice is about capacity:

  • Two HP48-200Ah — 19,200 Wh, about 1.5 hours WOT
  • Two HP48-250Ah — 24,000 Wh, about 1.9 hours

The HP48-105Ah cannot be used here. That pack is not series-capable, so it cannot make 96 V at all. This is the single most common mistake we see on EP-30 and EP-50 builds.

EP-50 (96 V, 275 A) — only one pack works

This is the one worth reading carefully. The EP-50 draws 275 A, and wiring packs in series raises voltage while leaving the current rating unchanged. So:

  • Two HP48-160Ah — 225 A continuous. Not enough.
  • Two HP48-200Ah — 250 A continuous. Still not enough.
  • Two HP48-250Ah — 400 A continuous. This is the one. 24,000 Wh, about 0.9 hours WOT.

Series wiring does not add current capability. If you take only one thing from this article, take that.

Charging: it is 54.6 V, not 58.4 V

Hi-Power's 48 V packs are 15-cell LiFePO4 — 48.0 V nominal, 54.6 V fully charged. A great many 48 V lithium batteries on the market are 16-cell, 51.2 V nominal and 58.4 V charged, and their chargers are not interchangeable with these.

Every Hi-Power pack we sell ships with the correct lithium charger included, so this only bites if you try to reuse something you already own. A lead-acid charger will not charge these correctly and voids the warranty. If you want faster turnaround on a large pack — and on 12,000 Wh you will — we stock Delta-Q QuiQ chargers we can program to the right profile. The packs accept up to 120 A charge current.

What to work out before you order

  1. Voltage match. 24 V motor, 24 V pack. 48 V motor, one 48 V pack. 96 V motor, two 48 V packs in series.
  2. Current headroom. Motor max current must sit inside the pack's continuous rating, with margin. Not at the limit.
  3. Usable energy against your actual running. Be honest about throttle and hours rather than sizing to a brochure figure.
  4. Physical fit and weight distribution. The 250Ah is 134 lb and 30" × 19" × 7" — a different proposition in a small boat than the 72 lb 160Ah. Where it sits changes how the boat trims.
  5. Fusing and disconnect. A pack that will deliver 400 A continuous and 800 A peak needs protection sized and placed properly, and that is not optional on a boat.

Being straight about documentation

We would rather tell you this than have you find out later. Hi-Power publish product specifications but do not publish test or certification documentation — we have found no UL 1973 listing, no UN38.3 test summary and no CE marking on their materials. For a golf cart that is unremarkable. For a vessel it is a conversation worth having, particularly if an insurer, a surveyor or an ABYC-compliant installation is involved. If your project needs that paperwork, tell us at the start and we will chase it or point you at a pack that has it. We are not going to imply a certification that is not there.

The figures in this article come from Elco's published outboard spec sheet and from Hi-Power's stated pack specifications. The pairing arithmetic is ours.

Ask us before you buy

Send us the outboard model, the boat, and a realistic picture of how you use it — hours, throttle, whether you need to get home against a tide. We will tell you which pack fits, and we will tell you when the answer is none of them. We work on electric propulsion systems for real boats and sit on ABYC's E-11 and E-13 committees, so this is the part of the job we actually enjoy.

Contact us · All Hi-Power lithium packs · Marine parts · Lithium chargers

Back to blog